Ακριβώς σε αυτό αναφέρομαι Τάκη αλλά το πρόβλημα ξεκινά από το καλώδιο, κοίτα το παρακάτω κείμενο:
When the professional video industry went to digital signals, it settled upon a standard--SDI, serial digital video--which was designed to be run in coaxial cables, where impedance can be controlled very tightly, and consequently, uncompressed, full-blown HD signals can be run hundreds of feet with no loss of information in SDI. For reasons known only to the designers of the DVI and HDMI standards, this very sound design principle was ignored; instead of coaxial cable, the DVI and HDMI signals are run balanced, through twisted-pair cable. The best twisted pair cables control impedance to about +/- 10%. When a digital signal is run through a cable, the edges of the bits (represented by sudden transitions in voltage) round off, and the rounding increases dramatically with distance. Meanwhile, poor control over impedance results in signal reflections--portions of the signal bounce off of the display end of the line, propagate back down the cable, and return, interfering with later information in the same bitstream. At some point, the data become unrecoverable, and with no error correction available, there's no way to restore the lost information.
Λόγω της αδυναμίας error correction στο HDMI, αυτό γίνεται αναγκαστικά στη συσκευή. Ένα καλώδιο με μεγάλη απώλεια σήματος θα δημιουργήσει τέτοια κενά στην ακολουθία 0,1 που θα είναι πολύ δύσκολο να επανορθώσει μία φθηνή συσκευή με Motion Compensation που είναι το καλύτερο αλλά προυποθέτει πολύ δυνατή επεξεργασία. Οι φθηνές συσκευές χρησιμοποιούν Weaving Blending ή Selective Bleading, μέθοδοι που σίγουρα επηρεάζουν αρνητικά την εικόνα. Σε κάθε περίπτωση , όσο μεγαλύτερη απώλεια στο σήμα, τόσο χειρότερη εικόνα. Σε συνδέσεις πάνω από τα 10 μέτρα έχω διαπιστώσει πάρα πολλές διαφορές.
When the professional video industry went to digital signals, it settled upon a standard--SDI, serial digital video--which was designed to be run in coaxial cables, where impedance can be controlled very tightly, and consequently, uncompressed, full-blown HD signals can be run hundreds of feet with no loss of information in SDI. For reasons known only to the designers of the DVI and HDMI standards, this very sound design principle was ignored; instead of coaxial cable, the DVI and HDMI signals are run balanced, through twisted-pair cable. The best twisted pair cables control impedance to about +/- 10%. When a digital signal is run through a cable, the edges of the bits (represented by sudden transitions in voltage) round off, and the rounding increases dramatically with distance. Meanwhile, poor control over impedance results in signal reflections--portions of the signal bounce off of the display end of the line, propagate back down the cable, and return, interfering with later information in the same bitstream. At some point, the data become unrecoverable, and with no error correction available, there's no way to restore the lost information.
Λόγω της αδυναμίας error correction στο HDMI, αυτό γίνεται αναγκαστικά στη συσκευή. Ένα καλώδιο με μεγάλη απώλεια σήματος θα δημιουργήσει τέτοια κενά στην ακολουθία 0,1 που θα είναι πολύ δύσκολο να επανορθώσει μία φθηνή συσκευή με Motion Compensation που είναι το καλύτερο αλλά προυποθέτει πολύ δυνατή επεξεργασία. Οι φθηνές συσκευές χρησιμοποιούν Weaving Blending ή Selective Bleading, μέθοδοι που σίγουρα επηρεάζουν αρνητικά την εικόνα. Σε κάθε περίπτωση , όσο μεγαλύτερη απώλεια στο σήμα, τόσο χειρότερη εικόνα. Σε συνδέσεις πάνω από τα 10 μέτρα έχω διαπιστώσει πάρα πολλές διαφορές.